Black And Decker Vacuum Cleaner Filter [Detailed Guide]

If you have a question about a Black and Decker vacuum filter, you’ve in the right place. Here we’ll answer the questions you have about a Black and Decker vacuum filter . . .

Table of Contents

Black And Decker Cordless Vacuum Cleaner Filter Cleaning – How To

Follow the steps below to clean the filters in two types of Black and Decker cordless vacuum cleaners . . .

How to clean the filter in a Black and Decker vacuum cleaner with a door

Follow the steps below to clean the filter of your Black and Decker vacuum cleaner with a door . . .

Step 1. Turn the vacuum cleaner off and unplug it from the power outlet before you begin the cleaning process. Working on your Black and Decker cordless vacuum cleaner while it is turned on or plugged into the power outlet can be dangerous.

Step 2. Open the door of the vacuum cleaner to access the vacuum canister. Empty the vacuum canister over a trash can. Tap on the bottom of the canister to get rid of all the dust.

Step 3. Press the release button on the vacuum cleaner to disconnect the canister from the rest of the machine.

Step 4. Take the vacuum canister out of the vacuum cleaner and set it aside.

Step 5. Disconnect the pleated filter from the vacuum cleaner canister.

Step 6. Tap the filter on the side of a trash can or sink to get rid of loose dirt.

Step 7. Use a dry piece of cloth or tissue or a soft brush to get rid of stubborn dirt. Make sure you do not rub the filter too violently.

Step 8. Wipe the internal part of the vacuum cleaner canister with a dry piece of cloth or tissue.

Step 9. Once the filter and canister are completely clean, reconnect the filter to the vacuum canister.

Step 10. Reconnect the vacuum canister to the vacuum cleaner and close the lid of the canister. You can start using your Black and Decker cordless vacuum cleaner now.

How to clean the filter of a Black and Decker cordless vacuum cleaner with a nozzle

Follow the steps below to properly clean the filter of your Black and Decker cordless vacuum cleaner with a nozzle . . .

Step 1. Turn the vacuum cleaner off and unplug it from the power outlet before you begin the cleaning process. Cleaning your machine while it is turned on can be dangerous

Step 2. Press the tabs on the side of the vacuum cleaner to disconnect the nozzle from the vacuum cleaner.

Step 3. Take the nozzle out of the vacuum cleaner and set it aside.

Step 4. Empty the vacuum cleaner canister.

Step 5. Disconnect the vacuum canister from the vacuum cleaner.

Step 6. Pull the plastic pre filter and the pleated filter out of the vacuum cleaner canister.

Step 7. Tap the pre filter and the pleated filter on the side of a trash can or sink to get rid of loose.

Step 8. Twist the pre filter counter clockwise to disconnect it from the pleated filter.

Step 9. Wash the filters with warm water and a mild detergent.

Step 10. Leave the filters to dry. Make sure the filters are completely dry before reconnecting them to the vacuum cleaner. Using your Black and Decker cordless vacuum cleaner with wet filters can cause the machine to malfunction.

Step 11. When the filters are completely dry, reattach them.

Step 12 Reconnect the filters to the vacuum cleaner canister.

Step 13. Reconnect the canister to the vacuum cleaner.

Step 14. Reconnect the nozzle to the vacuum cleaner. You can start using your Black and Decker vacuum cleaner again.

Black And Decker Air Swivel Vacuum Cleaner Filter Cleaning – How To

Follow the steps below to clean the filter of your Black and Decker air swivel vacuum cleaner properly . . .

Step 1. Turn the vacuum cleaner off and unplug it from the power outlet before you begin the cleaning process. Working on your Black and Decker air swivel vacuum cleaner while it is turned on or plugged into the power outlet can cause electrocution.

Step 2. Push the release button on the vacuum canister to disconnect it from the vacuum cleaner.

Step 3. Take the vacuum canister from the vacuum cleaner and set it aside.

Step 4. Push the lever at the bottom of the canister to open the lid and empty it.

Step 5. After emptying the vacuum canister, pull the filter tab on the side of the vacuum canister up to open the top lid of the canister.

Step 6. Lift out the cyclone piece in the middle of the vacuum canister.

Step 7. Disconnect the pre filter from the cyclone piece.

Step 8. Tap the filter on the side of a trash can or sink to get rid of loose dirt.

Step 9. Tap the cyclone on the side of a trash can or sink to get rid of loose dirt.

Step 10. Wash the pre filter and the cyclone under running water and leave them to dry.

Step 11. Make sure the filter and cyclone are completely dry before reconnecting them to the vacuum cleaner. Using your Black and Decker air swivel vacuum cleaner with a wet pre filter or cyclone can cause it to malfunction.

Step 12. When the filter and cyclone are completely dry, reattach them and reconnect them to the vacuum canister making sure to place them properly. You can tell that the filter and cyclone are properly secured when you hear it lock in place.

Step 13. Make sure the bottom lid of the canister is properly closed.

Step 14. Close the top lid of the vacuum canister.

Step 15. Reconnect the canister to the vacuum cleaner. Make sure the canister is properly placed.

Step 16. Push the little switch at the bottom of the vacuum canister to disconnect the post motor filter from the vacuum cleaner.

Step 17. Take the post motor filter out of the vacuum cleaner and set it aside.

Step 18. Tap the post motor filter on the side of a trash can or sink to get rid of loose dirt.

Step 19. Wash the post motor filter with warm water and a mild detergent and leave it to dry for about twenty four hours.

Step 20. Make sure the filter is completely dry before reconnecting it to the vacuum cleaner. Using your Black and Decker air swivel vacuum cleaner with a wet post motor filter can cause it to malfunction.

Step 21. When the post motor filter is completely dry, reconnect it to the vacuum cleaner. Make sure you remember to lock it in place with the little switch at the bottom of the vacuum canister.
You can start using your Black and Decker air swivel vacuum cleaner again.

Note: Do not try using the vacuum cleaner without the pre filter or post motor filter. Using your Black and Decker air swivel vacuum cleaner without its filters can cause it to malfunction.

Black And Decker Hand Vacuum Cleaner Filter Change – How To

Here we will show you how to change the filter of two types of Black and Decker hand vacuum cleaner . . .

How to change the filter of a Black and Decker hand vacuum cleaner with a door

Follow the steps below to learn how to change the filter of your Black and Decker hand vacuum cleaner with a door . . .

Step 1. Turn the vacuum cleaner off and unplug it from the power outlet before you begin. Working on your Black and Decker vacuum cleaner while it is turned on or plugged into the power outlet can cause electrocution.

Step 2. Open the door of the vacuum canister and empty it over a trash can.

Step 3. Disconnect the nozzle from the vacuum cleaner to gain access to the pleated filter.

Step 4. Put a new pleated filter in the place of the old one making sure to secure it properly.

Step 5. Reconnect the nozzle to the rest of the vacuum cleaner.

Step 6. Turn the vacuum cleaner back on and you can start using your machine now.

How to change the filter of your Black and Decker hand vacuum cleaner with a nozzle

Follow the steps below to change the filter of your Black and Decker hand vacuum cleaner with a nozzle . . .

Step 1. Turn the vacuum cleaner off and unplug it from the power outlet before you begin. It can be dangerous to work on your machine while it is turned on and plugged into the power outlet.

Step 2. Press the tabs on the side of the vacuum cleaner to disconnect the nozzle from it. Set the nozzle head aside.

Step 3. Empty the vacuum cleaner canister to gain access to the filters.

Step 4. Press the release button on the handle of the vacuum cleaner to disconnect the vacuum canister from the rest of the machine.

Step 5. Take the vacuum canister out of the vacuum cleaner and set it aside.

Step 6. Pull the pre filter and the pleated filter out of the vacuum cleaner and turn the pre filter counter clockwise to disconnect it from the pleated filter.

Step 7. Separate the filters.

Step 8. Put a new pre filter and pleated filter in the place of the old ones.

Step 9. Reconnect the vacuum canister to the vacuum cleaner.

Step 10. Reconnect the nozzle to the vacuum canister. You can start using your Black and Decker hand vacuum cleaner again now.

Black And Decker Lithium Hand Vacuum Cleaner Filter Cleaning – How To

Follow the steps below to clean the filter of your Black and Decker lithium hand vacuum cleaner properly . . .

Step 1. Make sure the vacuum cleaner is turned off and unplugged from the power outlet before you begin the cleaning process.

Step 2. Disconnect the nozzle of the vacuum cleaner to gain access to the vacuum canister.

Step 3. Empty the vacuum canister. Make sure to tap on the bottom of the vacuum cleaner to get rid of all the dust and debris in the vacuum canister.

Step 4. Disconnect the vacuum canister from the vacuum cleaner then take the filters out of the vacuum cleaner.

Step 5. Tap the filters on the side of a trash can or sink to get rid of loose dust.

Step 6. Wash the filters with warm water and a mild detergent. Wash the vacuum canister as well.

Step 7. Leave the filters to dry for about twenty fours hours before reconnecting it to the vacuum cleaner. Using your Black and Decker lithium hand vacuum cleaner can cause it to malfunction.

Step 8. When the filters are completely dry, reconnect them to the vacuum cleaner canister.