Is your Black and Decker vacuum not working well? You’re in the right place. Here we’ll identify the problem your vacuum cleaner has and show you proven solutions . . .
Table of Contents
Black And Decker Vacuum Cleaner Stopped Working – Why and How To Fix
If your Black and Decker vacuum cleaner stops working, the machine could have one of many problems. Keep on reading to figure out the problem your Black and Decker vacuum cleaner might have . . .
The vacuum cleaner battery might be low
If the battery of your Black and Decker vacuum cleaner is low, the machine won’t be able to work properly. To solve the problem, you will need to charge the vacuum cleaner. Follow the steps below to charge your Black and Decker vacuum cleaner. . .
Step 1. Turn the vacuum cleaner off before you begin. Charging your Black and Decker vacuum cleaner when it is turned can be dangerous.
Step 2. Plug the vacuum cleaner power cord into the power outlet, then turn the power outlet on.
Step 3. Leave the vacuum cleaner to charge for about five hours. You can tell that the vacuum cleaner is charging when you see the power indicator light flashing.
Step 4. When the vacuum cleaner is fully charged, turn the power outlet off and unplug the machine. You can tell that the vacuum cleaner is fully charged when the power indicator light stops flashing.
Step 5. Turn your Black and Decker vacuum cleaner back on and check if it is working like it is supposed to now.
The battery might be bad
If the battery of your Black and Decker vacuum cleaner is bad, the machine won’t be able to work properly. To solve the problem, you will need to replace the vacuum battery. Follow the steps below to replace your Black and Decker vacuum cleaner battery . . .
Step 1. Leave the battery of the vacuum cleaner to drain completely before you try replacing it. Replacing your Black and Decker vacuum cleaner when it is fully charged can be dangerous.
Step 2. Turn the vacuum cleaner off and unplug from the power outlet before you begin. Never work on your Black and Decker vacuum cleaner when it is turned on or plugged into the power outlet.
Step 3. Make sure you wear gloves while replacing the battery of your Black and Decker vacuum cleaner because the battery might be damaged or leaking. Also remember to wash your hands afterwards.
Step 4. Flip the vacuum cleaner over and lay it on a flat surface.
Step 5. Remove the screws at the bottom of the handle of the vacuum cleaner and keep the screws in a safe place.
Step 6. Press the two plastic tabs near the place where the screws came out from to disconnect the underside of the machine from the rest of the vacuum cleaner.
Step 7. Take the underside out of the vacuum cleaner and set it aside. You will see the vacuum cleaner battery inside.
Step 8. Remove the screws holding the battery in place and keep them in a safe place.
Step 9. Slide the battery out of its chamber and set it aside.
Step 10. To dispose of a Black and Decker vacuum cleaner battery properly, you will need to recycle it.
Step 11. Put a new Black and Decker vacuum cleaner battery in the place of the old one and use the old screws to hold the battery in place.
Step 12. Put the underside of the vacuum cleaner back in its place then put the old screws back in their places. Use the plastic tabs to lock the underside of the vacuum cleaner in place.
Step 13. Flip the vacuum cleaner over again and keep it in the upright position.
Step 14. Leave the vacuum cleaner to charge for about five hours until it is full.
Step 15. Unplug the vacuum cleaner from the power outlet once it is full.
Step 16. Turn your Black and Decker vacuum cleaner back on and check if it is working like it is supposed to now.
Black And Decker Air Swivel Vacuum Cleaner Not Working – Why and How To Fix
If your Black and Decker air swivel vacuum cleaner is not working properly, the machine could have one of six problems. Keep on reading to figure out the problem your Black and Decker vacuum cleaner has and how to fix it . . .
The vacuum cleaner hose might be blocked
If the hose of your Black and Decker air swivel vacuum cleaner is blocked, the machine won’t be able to work properly. To solve the problem, you will need to unblock the vacuum hose. Follow the steps below to unclog your Black and Decker air swivel vacuum cleaner hose . . .
Step 1. Turn the vacuum cleaner off and unplug it from the power outlet before you begin. Cleaning your Black and Decker air swivel vacuum cleaner hose when it is turned on and plugged into the power outlet can electrocution.
Step 2. Disconnect the top of the hose from the vacuum cleaner.
Step 3. Twist the bottom part of the vacuum cleaner hose to disconnect it from the vacuum. Take the vacuum cleaner hose out and set it aside.
Step 4. Use a long and thin pole to push out the object that is blocking the vacuum hose.
Step 5. Run hot water through the hose to clean out any stubborn dirt in it.
Step 6. Leave the hose to dry for about twenty four hours before reconnecting it to the vacuum cleaner. Using your Black and Decker vacuum cleaner with a wet hose can cause it to malfunction.
Step 7. When the vacuum hose is completely dry, reconnect it to the vacuum cleaner.
Step 8. Turn your Black and Decker air swivel vacuum cleaner back on and check if it is working like it is supposed to now.
The filter might be dirty
If the filter of your Black and Decker air swivel vacuum cleaner is dirty, the machine won’t be able to work properly. To solve the problem, you will need to clean the filter. Follow the steps below to clean your Black and Decker air swivel vacuum cleaner . . .
Step 1. Turn the vacuum cleaner off and unplug it from the power outlet before you begin the cleaning process. Never clean your Black and Decker air swivel vacuum cleaner filter when the machine is turned on or plugged into the power outlet.
Step 2. Press the release button on the handle of the vacuum cleaner canister to disconnect it from the vacuum cleaner.
Step 3. Take the vacuum canister out of the vacuum cleaner and set it aside.
Step 4. Lift the tab on the vacuum canister up to open the top of it.
Step 5. Open the bottom part of the canister over a trash can to empty it.
Step 6. Lift the filter and cyclone piece out of the vacuum canister.
Step 7. Separate the cyclone piece and the pre filter.
Step 8. Tap the pre filter and the cyclone piece on the side of a trash can or sink to get rid of loose dirt.
Step 9. Wash the filter and cyclone piece under running water and leave them to dry. Make sure the pre filter and cyclone piece are completely dry before reconnecting them to the vacuum canister.
Using your Black and Decker air swivel vacuum cleaner with a wet filter or cyclone piece can cause it to malfunction.
Step 10. When the pre filter and cyclone piece are completely dry, reattach them.
Step 11. Reconnect the cyclone and filter to the vacuum canister.
Step 12. Close the lid of the vacuum canister then reconnect it to the vacuum cleaner.
Step 13. Push the little switch at the bottom of the vacuum cleaner to disconnect the post motor filter from the rest of the machine.
Step 14.Take the post motor filter out of the vacuum cleaner and set it aside.
Step 15. Tap the post motor filter on the side of a trash can or sink to get rid of loose dirt.
Step 16. Wash the post motor filter under running water and leave it to dry.
Step 17. Make sure the post motor filter is completely dry before reconnecting it to the vacuum cleaner. Using your Black and Decker air swivel vacuum cleaner with a wet post motor filter is dangerous.
Step 18. When the post filter is completely dry, reconnect it to the vacuum cleaner.
Step 19. Lock the post motor filter in place with the switch at the bottom of the vacuum cleaner.
Step 20. Turn your Black and Decker air swivel vacuum cleaner back on and check if it is working like it is supposed to now.
The vacuum cleaner canister/bag is too full
If the canister of your Black and Decker air swivel vacuum cleaner is too full, the machine won’t be able to work properly. To solve the problem, you will need to empty the vacuum canister. Follow the steps below to empty your Black and Decker air swivel vacuum cleaner canister . . .
Step 1. Turn your Black and Decker vacuum cleaner off and unplug it from the power outlet.
Step 2. Press the release button on the handle of the canister to disconnect it from the vacuum cleaner.
Step 3. Open the bottom of the vacuum canister.
Step 4. Empty the vacuum canister over a trash can.
Step 5. Close the bottom lid of the vacuum canister.
Step 6. Reconnect the vacuum canister to the vacuum cleaner and make sure you lock it in place. You can tell that the vacuum canister is properly secured when you hear it lock with a click.
Step 7. Turn your Black and Decker air swivel vacuum cleaner back on and check if it is working like it is supposed to now.
The vacuum cleaner belt is bad
If the belt of your Black and Decker air swivel vacuum cleaner is bad, the machine won’t be able to work properly. To solve the problem, you will need to replace the vacuum cleaner belt. Follow the steps below to replace your Black and Decker air swivel vacuum cleaner belt . . .
Step 1. Turn the vacuum cleaner off and unplug it from the power outlet before you begin. Never work on your Black and Decker air swivel vacuum cleaner when it is turned on or plugged into the power outlet.
Step 2. Flip the vacuum cleaner over and lay it on a flat surface.
Step 3. Use a Phillips head screwdriver to remove the six screws holding the brush roller cover in place. Keep the screws in a safe place.
Step 4. Take the brush roller cover out and set it aside.
Step 5. Take the brush roller out of the vacuum cleaner then slide it through the vacuum belt. Set the brush roller aside.
Step 6. Disconnect the vacuum belt from the vacuum cleaner and set it aside.
Step 7. Get a new Black and Decker air swivel vacuum cleaner belt and put it in the place of the old one.
Step 8. Slide the old brush roller through the belt again then put it back into the vacuum cleaner.
Step 9. Put the brush roller cover back on then put the six screws back in their places.
Step 10. Flip the vacuum cleaner over again and keep it in the upright position.
Step 11. Turn the vacuum cleaner back on and check if it is working like it is supposed to now.
The brush roller is dirty
If the brush roller of your Black and Decker air swivel vacuum cleaner is dirty, the machine won’t be able to work properly. To solve the problem, you will need to clean the brush roller. Follow the steps below to clean a Black and Decker air swivel vacuum cleaner brush roller. . .
Step 1. Turn the vacuum cleaner off and unplug it from the power outlet before you begin the cleaning process. Never clean your Black and Decker air swivel vacuum cleaner when it is turned on or plugged into the power outlet.
Step 2. Flip the vacuum cleaner over and lay it on a flat surface.
Step 3. Use a Phillips head screwdriver to remove the screws holding the brush roller cover in place. Keep the screws in a safe place.
Step 4. Take the brush roller cover out and set it aside.
Step 5. Take the brush roller out of the brush chamber and slide it through the vacuum belt.
Step 6. Use a pair of scissors to cut off any hair or thread that may be stuck on the vacuum cleaner brush roller.
Step 7. Use a dry piece of cloth or tissue or a soft brush to clean any dust that may be on the vacuum brush cover or in the chamber.
Step 8. When the brush roller is completely clean, reconnect it to the vacuum cleaner then slide it through the vacuum belt again.
Step 9. Reconnect the brush cover to the vacuum cleaner and use the screws to lock it in place.
Step 10. Flip the vacuum cleaner over and keep it in the upright position.
Step 11. Turn the vacuum cleaner back on and check if it is working like it is supposed to now.
The brush roller is bad
If the brush roller of your Black and Decker air swivel vacuum cleaner is bad, the machine won’t be able to work properly. To solve the problem, you will need to replace the brush roller. Follow the steps below to replace your Black and Decker air swivel vacuum cleaner brush roller . . .
Step 1. Turn the vacuum cleaner off and unplug it from the power outlet before you begin. Working on your Black and Decker air swivel vacuum cleaner cleaner when it is turned on or plugged into the power outlet can cause electrocution.
Step 2. Flip the vacuum cleaner over and lay it on a flat surface.
Step 3. Use a Phillips head screwdriver to remove the six screws holding the brush cover in place. Take the brush cover out and set it aside.
Step 4. Take the brush roller out of the vacuum cleaner then slide it through the vacuum belt.
Step 5. Put a new Black and Decker vacuum cleaner brush roller in the place of the old one and slide it through the old vacuum belt.
Step 6. Put the brush roller cover back on then put the six screws back in their places.
Step 7. Flip the vacuum cleaner over again and keep it in the upright position.
Step 8. Turn your Black and Decker air swivel vacuum cleaner back on and check if it is working like it is supposed to now.
