Shark Vacuum Cleaner Filter [Problems, Solutions and Guide]

If you have a question about a Shark vacuum cleaner filter, you’re in the right place. Here we will answer questions you might have about a Shark vacuum filter . . .

Table of Contents

Can I Wash A Shark Vacuum Cleaner Filter?

Yes, your Shark vacuum cleaner comes with a washable hepa filter.

Can I Replace A Shark Vacuum Cleaner Filter?

Yes, you will need to replace the filter of your Shark vacuum cleaner once every two to three months to keep your machine in good shape.

How To Replace A Shark Vacuum Cleaner Filter

Follow the steps below to replace the filters of different kinds of Shark vacuum cleaners . . .

How to replace the filter of a Shark Rotator Lift-Away vacuum cleaner

Follow the steps below to replace the filter of your Shark rotator lift-away vacuum cleaner . . .

Step 1. Always make sure your vacuum cleaner is turned off and unplugged from the power outlet before you begin. Replacing any part of your Shark rotator lift-away vacuum cleaner when the machine is turned on or plugged into the power outlet can cause electrocution.

Step 2. At the bottom of the vacuum canister, you will see a filter cover. Take the filter cover out of the vacuum cleaner and set it aside.

Step 3. Pull the old filter out of the vacuum cleaner and set it aside.

Step 4. Put a new Shark rotator lift-away vacuum cleaner filter in place of the old one.

Step 5. Put the filter cover back on and make sure to lock it in place properly.

Step 6. To gain access to the second filter, you will need to disconnect the vacuum canister from the vacuum cleaner.

To disconnect the dust container of your Shark rotator lift-away vacuum cleaner, press the two buttons on the handle of the canister and separate it from the rest of the machine. Set the rest of your Shark vacuum cleaner aside.

Step 7. Take the foam filter and felt filter out of the filter chamber.

Step 8. Put a new Shark rotator lift-away vacuum cleaner felt filter in the place of the old one.

Step 9. Take the foam filter out of its casing and set it aside.

Step 10. Put a new foam filter of the same kind in the place of the old one.

Step 11. Reconnect the vacuum canister to the vacuum cleaner. You can tell that the vacuum canister is properly secured when you hear it lock with a click.

Step 12. Turn your Shark rotator lift-away vacuum cleaner back on and you can start cleaning with it again.

How to replace the filter of a Shark navigator lift-away vacuum cleaner

Follow the steps below to replace the filter of your Shark navigator lift-away vacuum cleaner . . .

Step 1. Ensure your Shark vacuum cleaner is turned off and unplugged from the power outlet before you start.

Step 2. At the bottom of the vacuum canister, you will see the filter cover. Press the lever at the bottom of the filter cover to disconnect it from the rest of the vacuum cleaner. Set the filter cover side.

Step 3. Pull the old filter out of the filter chamber and set it aside.

Step 4. Put a new Shark vacuum cleaner filter of the same kind in the place of the old one.

Step 5. Unhook the latches on the side of the vacuum cleaner to disconnect the vacuum canister from the rest of the machine. Set the vacuum canister aside.

Step 6. Take the foam filter and felt filter out of the filter chamber and set them aside.

Step 7. Put new Shark vacuum cleaner filters of the same kind in the place of the old ones.

Step 8. Reconnect the vacuum canister to the vacuum cleaner and use the latches that you unhooked earlier to lock it in place again.

Step 9. Turn your Shark navigator lift-away vacuum cleaner back on and you can start cleaning with it again.

How to replace the filter of a Shark rocket deluxe pro ultra light vacuum cleaner

Follow the steps below to replace the filter of your Shark rocket deluxe pro ultra light vacuum cleaner . . .

Step 1. Ensure that your vacuum cleaner is turned off and unplugged from the power outlet before you start. Replacing any part of your Shark vacuum cleaner when the machine is turned on or plugged into the power outlet can cause electrocution.

Step 2. On the top of the vacuum cleaner, you will see the pre-motor filter cover. Take the filter cover out of the vacuum cleaner and set it aside.

Step 3. Take the old pre-motor filter out of the vacuum cleaner and set it aside.

Step 4. Put a new Shark vacuum cleaner pre-motor filter of the same kind in the place of the old one.

Step 5. Put the pre-motor filter cover back on and make sure to lock it in place properly. You can tell that the filter cover is properly secured when you hear it lock with a click.

Step 6. Flip the vacuum cleaner over.

Step 7. At the bottom of the vacuum cleaner, you will see another filter. Take the filter out and set it aside.

Step 8. Put a new Shark vacuum cleaner filter of the same kind in the place of the old one. Make sure to lock the new filter in place properly.

Step 9. Flip your vacuum cleaner over again.

See also  Electrolux Vacuum Cleaner Working [Problems and Solutions]

Step 10. Turn your Shark rocket deluxe pro ultra light vacuum cleaner back on and you can start cleaning with it again.

How to replace the filter of a Shark rocket duo clean cordless vacuum cleaner

Follow the steps below to replace the filter of your Shark rocket duo clean cordless vacuum cleaner . , .

Step 1. Make sure your Shark vacuum cleaner is turned off and unplugged from the power outlet before you begin.

Step 2. Disconnect the vacuum hose from the rest of the vacuum cleaner and set it aside.

Step 3. Disconnect the vacuum canister from the rest of the vacuum cleaner and set it aside.

Step 4. Open the cover on the top of the vacuum cleaner to gain access to the first filter. Set the filter cover aside.

Step 5. Take the foam filters out of the vacuum cleaner and set them aside.

Step 6. Put a new Shark vacuum cleaner filter of the same kind in the place of the old one.

Step 7. Put the filter cover back on.

Step 8. Flip the vacuum cleaner over to gain access to the second filter.

Step 9. Take the filter and filter cover out of the vacuum cleaner.

Step 10. Take the second filter out of the filter cover and set it aside.

Step 11. Put a new filter of the same kind in the place of the old one.

Step 12. Put the new filter and filter cover back in the vacuum cleaner.

Step 13. Reconnect the vacuum canister to the vacuum cleaner.

Step 14. Reconnect the vacuum hose to the vacuum cleaner.

Step 15. Turn your Shark rocket duo clean cordless vacuum cleaner back on and you can start cleaning with it again.

How to replace the filter of a Shark ion robot vacuum cleaner

Follow the steps below to replace the filter of your Shark ion robot vacuum cleaner . . .

Step 1. Always make sure your vacuum cleaner is turned off and unplugged from the power outlet before you start. Replacing any part of your Shark robot vacuum cleaner when the machine is turned on or plugged into the power outlet can cause electrocution.

Step 2. Disconnect the vacuum tray from the vacuum cleaner. Set the rest of your vacuum cleaner aside.

Step 3. Push the tabs in the middle of the vacuum tray to open it. Lean the cover of the vacuum tray backwards then empty it over a trash can if necessary.

Step 4. At the back of the vacuum tray, you will see a little orange filter. Take the filter out and set it aside.

Step 5. Put a new Shark vacuum cleaner filter of the same kind in the place of the old one.

Step 6. Close the lid of the vacuum tray then reconnect it to the vacuum cleaner.

Step 7. Turn your Shark ion robot vacuum cleaner back on and you can start cleaning with it again.

How To Clean The Filters Of Shark Vacuum Cleaner

Follow the steps below to clean the filters of different kinds of Shark vacuum cleaners . . .

How to clean the filters of a Shark navigator zero lift away vacuum cleaner

Follow the steps below to clean the filters of your Shark navigator zero lift away vacuum cleaner properly . . .

Step 1. Make sure your vacuum cleaner is turned off and unplugged from the power outlet before you begin the cleaning process. Cleaning the filters of your Shark vacuum cleaner when the machine is turned on or plugged into the power outlet can cause electrocution.

Step 2. Disconnect the canister from the vacuum cleaner to gain access to the vacuum filter. Set the vacuum canister aside.

Step 3. Take the foam filter out of the filter chamber and set it aside. Take out the felt filter as well.

Step 4. Wash the filters with water and no detergent. Leave the filters to dry for about twenty four hours before reconnecting them to the vacuum cleaner. Using your Shark navigator zero lift away vacuum cleaner with a wet filter can cause it to malfunction.

Step 5. When they are completely dry, reconnect the felt filter and foam filter to the vacuum cleaner.

Step 6. Reconnect the vacuum canister to the vacuum cleaner and make sure to lock it in place properly.

Step 7. Press the button at the bottom of the filter cover to gain access to the second filter. Take the filter cover out and set it aside.

Step 8. Take the second filter out of the vacuum cleaner. Set the rest of the vacuum cleaner aside.

Step 9. Wash the filter with water and no detergent then leave it to dry.

Step 10. When it is completely dry, reconnect the filter to the bottom of the vacuum canister.

Step 11. Reconnect the filter cover to the vacuum cleaner.

Step 12. Turn your Shark navigator zero lift away vacuum cleaner back on and you can start cleaning with it again.

How to clean the filters of a Shark rocket deluxe pro ultra light vacuum cleaner

Follow the steps below to clean the filters of your Shark rocket deluxe pro ultra light vacuum cleaner properly . . .

Step 1. Before you start the cleaning process, turn your vacuum cleaner off and unplug it from the power outlet.

Step 2. Open the cover on the top of the vacuum cleaner to gain access to the first two filters. Set the filter cover aside.

Step 3. Take the foam filter and the felt filter out of the vacuum cleaner. Set the rest of your vacuum cleaner aside.

Step 4. Wash the foam filter and felt filter with water and no detergent. Leave the filters to dry.
Make sure the filters are completely dry before reconnecting them to the vacuum cleaner. Using your Shark vacuum cleaner with a wet filter can cause it to malfunction.

Step 5. When they are completely dry, reconnect the felt filter and the foam filter to your vacuum cleaner .

Step 6. Put the filter cover back on and make sure to lock it in place properly.

Step 7. Flip the vacuum cleaner over to gain access to the last filter.

Step 8. Take the filter and filter cover out of the vacuum cleaner and then set the rest of your machine aside.

Step 9. Take the filter out of the filter cover. Set the filter cover aside.

Step 10. Wash the filter with water and no detergent. Leave the filter dry.

Step 11. When it is completely dry, reconnect the filter to the filter holder.

Step 12. Reconnect the filter and filter holder to the vacuum cleaner.

Step 13. Flip the vacuum cleaner over again.

Step 14. Turn your Shark rocket deluxe pro ultra light vacuum cleaner back on and you can start cleaning with it again.

How to clean the filter of your Shark ion robot vacuum cleaner

Follow the steps below to clean the filter of your Shark ion robot vacuum cleaner . . .

Step 1. Ensure that your vacuum cleaner is turned off and unplugged from the power outlet before you begin the cleaning process.

Step 2. Disconnect the vacuum tray from the vacuum cleaner. Set the rest of your vacuum cleaner aside.

See also  How to Clean Dog Poop Smell Out of Carpet: The Ultimate DIY Guide

Step 3. At the back of the vacuum tray, you will see a little orange filter. Take the filter out of the vacuum tray. Set the vacuum tray aside.

Step 4. Tap the filter on the side of a trash can or sink to get rid of loose dirt.

Step 5. Wash the filter with water and no detergent. Leave the filter to dry. Make sure the filter is completely dry before reconnecting it to the vacuum cleaner. Using your Shark ion robot vacuum cleaner with a wet filter can cause it to malfunction.

Step 6. When it is completely dry, reconnect the filter to the vacuum tray. Make sure to lock it in place properly.

Step 7. Reconnect the vacuum tray to your vacuum cleaner.

Step 8. Turn your Shark ion robot vacuum cleaner back on and you can start cleaning with it again.

How to clean the filters of a Shark rotator lift away vacuum cleaner

Follow the steps below to clean the filters of your Shark rotator lift away vacuum cleaner . . .

Step 1. Always remember to turn your vacuum cleaner off and unplug it from the power outlet before you begin the cleaning process. Cleaning the filters of your Shark rotator lift away vacuum cleaner when the machine is plugged into the power outlet can cause electrocution.

Step 2. At the bottom of the vacuum canister, you will see a little filter cover. Take the filter cover out of the vacuum cleaner and set it aside.

Step 3. Take the filter out of the vacuum cleaner. Set the rest of your vacuum cleaner aside.

Step 4. Wash the filter with water and no detergent. Leave the filter to dry. Make sure the filter is completely dry before reconnecting it to the vacuum cleaner. Using your Shark rotator lift away vacuum cleaner with a wet filter can cause it to malfunction.

Step 5. Reconnect the filter to the vacuum cleaner once it is completely dry.

Step 6. Reconnect the filter cover to the bottom of the vacuum cleaner.

Step 7. To gain access to the other two filters, you will need to disconnect the vacuum canister from the vacuum cleaner.

To disconnect the canister from your Shark rotator lift away vacuum cleaner, press the two buttons on the top of the dust container then separate it from the rest of your machine. Set the rest of the vacuum canister aside.

Step 8. Take the felt filter and the foam filter out of the filter chamber then set the rest of the vacuum cleaner aside.

Step 9. Wash the foam and felt filter with water and no detergent then leave them to dry.

Step 10. When they are completely dry, reconnect the foam and the felt filter to the filter chamber.

Step 11. Reconnect the vacuum canister to the vacuum cleaner and make sure to lock it in place properly.

Step 12. Turn your Shark rotator lift away vacuum cleaner back on and you can start cleaning with it again.

How to clean the filters of a Shark rocket duo clean cordless vacuum cleaner

Follow the steps below to replace the filters of your Shark rocket duo clean cordless vacuum cleaner . . .

Step 1. Turn your vacuum cleaner off and unplug it from the power outlet before you start the cleaning process.

Step 2. Disconnect the vacuum hose from the rest of the vacuum cleaner and set it aside.

Step 3. Disconnect the vacuum canister from the rest of the vacuum cleaner and set it aside.

Step 4. Disconnect the cover on top of the vacuum cleaner to gain access to the filter filter. Set the filter cover aside.

Step 5. Take the first filter out of the vacuum cleaner and set it aside.

Step 6. Open the cover at the back of the vacuum cleaner to gain access to the second filter. Take the second filter out of the filter cover. Set the filter cover aside.

Step 7. Tap the first filter on the side of a trash can or sink to get rid of loose dirt.

Step 8. Wash the filters with water and no detergent. Leave the filters to dry.

Step 9. Make sure the filters are completely dry before reconnecting them to the vacuum cleaner. Using your Shark rocket duo clean cordless vacuum cleaner with a wet filter can cause it to malfunction.

Step 10. When they are completely dry, reconnect the filters to the vacuum cleaner then put the filter covers back on.

Step 11. Reconnect the vacuum hose to the vacuum cleaner.

Step 12. Turn your Shark rocket duo clean cordless vacuum cleaner back on and you can start cleaning with it again.

Shark Vacuum Cleaner Filter Getting Hot – Why and How To Fix

If the filter of your Shark vacuum cleaner is getting hot, the problem could be that some parts of the machine are dirty or clogged. Keep on reading to figure out and to solve the problem your Shark vacuum cleaner has . . .

The whole vacuum cleaner is overheating

If your Shark vacuum cleaner is overheating, the filter of the machine will also overheat. To solve the problem, turn the vacuum cleaner off and unplug it from the power outlet then leave it to cool down for about 45 minutes.

After leaving it to cool down, turn your Shark vacuum cleaner back on and check if it is working like it is supposed to now.

The filters of the machine are dirty

If the filters of your Shark vacuum cleaner are dirty, it can cause the whole machine to overheat. To solve the problem, you will need to clean the vacuum cleaner filter. After cleaning the filter of your Shark vacuum cleaner, it should stop overheating now.

shark vacuum cleaner filter

The dust container is too full

If the dust container of your Shark vacuum cleaner is too full, the machine won’t be able to work without overheating. To solve the problem, you will need to empty the dust container. Follow the steps below to empty the dust container of three different kinds of Shark vacuum cleaners . . .

How to empty the dust container of a Shark rotator lift away vacuum cleaner

Follow the steps below to empty the dust container of your Shark rotator lift away vacuum cleaner . . .

Step 1. Make sure your machine is turned off and unplugged from the power outlet before you start.

Step 2. To disconnect the dust container from the vacuum cleaner, press the two buttons on the handle of the canister and separate it from the rest of your machine.

Step 3. Open the lid of the vacuum canister then empty it over a trash can. Wipe the inside of the canister with a dry piece of cloth or tissue if necessary.

Step 4. When it is completely empty, reconnect the vacuum canister to the vacuum cleaner and make sure to lock it in place properly.

Step 5. Turn your Shark rotator lift away vacuum cleaner back on and check if itn working like it is supposed to now.

How to empty the dust container of a Shark navigator lift away vacuum cleaner

Follow the steps to empty the dust container of your Shark navigator lift away vacuum cleaner . .

See also  How to Clean Carpet Every Day: The Ultimate Routine for Healthy Carpets

Step 1. Always ensure that your vacuum cleaner is turned off and unplugged from the power outlet before you begin the emptying process.

Step 2. Unhook the latches on the side of the vacuum cleaner to disconnect the dust container from the rest of your machine.

Step 3. Take the dust container out of the vacuum cleaner and then set the rest of your machine aside.

Step 4. Open the lid of the vacuum canister and then empty it over a trash can. Wipe the internal part of the canister with a dry piece of cloth or tissue if necessary.

Step 5. When it is completely empty, reconnect the vacuum canister to the vacuum cleaner and use the latches on the side of your machine to lock it in place properly.

Step 6. Turn your Shark navigator lift away vacuum cleaner back on and check if it is working like it is supposed to now.

How to empty the dust container of a Shark ion robot vacuum cleaner

Follow the steps below to empty the dust container of your Shark ion robot vacuum cleaner . . .

Step 1. Turn your Shark robot vacuum cleaner off and unplug it from the power outlet before you start the emptying process.

Step 2. Disconnect the vacuum tray from your vacuum cleaner. Set the rest of your vacuum cleaner aside.

Step 3. Press the tabs in the middle of the dust container to open it.

Step 4. Empty the vacuum tray over a trash can.

Step 5. Close the lid of the vacuum tray and then reconnect it to your vacuum cleaner.

Step 6. Turn your Shark ion robot vacuum cleaner back on and check if it is working like it is supposed to now.

The vacuum hose it clogged

If the hose of your Shark vacuum cleaner is clogged, the machine won’t be able to work without overheating. To solve the problem, you will need to clean the vacuum hose. Follow the steps below to clean the hose of your Shark vacuum cleaner . . .

Step 1. Turn your vacuum cleaner off and unplug it from the power outlet before you begin the cleaning process. Cleaning any part of your Shark vacuum cleaner when the machine is turned on or plugged into the power outlet can cause electrocution.

Step 2. Disconnect the vacuum hose from the vacuum cleaner. Set the rest of your vacuum cleaner aside.

Step 3. Get a long thin rod and use it to push out anything that may be blocking the vacuum hose.

Step 4. If necessary, run some water through the hose to get rid of more stubborn dirt. Leave the hose to dry.

Step 5. When it is completely dry, reconnect the vacuum hose to the vacuum cleaner.

Step 6. Turn your Shark vacuum cleaner back on and check if it is working like it is supposed to now.

The brush head attachments are dirty

If the brush head attachment of your Shark vacuum cleaner is clogged, the machine won’t be able to work without overheating. To solve the problem, you will need to clean the brush head attachment. Follow the steps below to clean the brush head attachment of different kinds of Shark vacuum cleaners properly . . .

How to clean the brush roller of a Shark rocket duo clean zero cordless vacuum cleaner

Follow the steps below to clean the brush roller of your Shark rocket duo clean zero cordless vacuum cleaner . . .

Step 1. Make sure your vacuum cleaner is turned off and unplugged from the power outlet before you begin the cleaning process. Cleaning the brush roller of your Shark vacuum cleaner when your machine is turned on or plugged into the power outlet can cause electrocution.

Step 2. Press the two buttons on the top of the brush head attachment to disconnect the brush roller cover from the rest of the machine.

Step 3. Take the brush roller cover out of the vacuum cleaner and set it aside.

Step 4. Carefully take out any hair or thread that may be in the main brush roller.

Step 5. Disconnect the second brush roller from the vacuum cleaner. Set the rest of your vacuum cleaner aside.

Step 6. Get a dry piece of cloth or tissue and use it to wipe off any dirt that may be on the second brush roller.

Step 7. When it is completely clean, reconnect the brush roller to the vacuum cleaner.

Step 8. Reconnect the brush roller cover to the vacuum cleaner and make sure to lock it in place properly.

Step 9. Turn your Shark rocket duo clean zero vacuum cleaner back on and check if it is working like it is supposed to now.

How to clean the brush roller of a Shark rocket powerhead vacuum cleaner

Follow the steps below to clean the brush roller of your Shark rocket powerhead vacuum cleaner . . .

Step 1. Always remember to turn your vacuum cleaner off and unplug it from the power outlet before you start the cleaning process.

Step 2. Open the cover of the brush roller and lean it backwards.

Step 3. Take the brush roller out of the vacuum cleaner and then set the rest of your machine aside.

Step 4. Get a pair of scissors and use it to carefully cut off any hair or thread that may be stuck on the brush roller. Take the hair or thread out of the brush roller and throw it away.

Step 5. If necessary, you can wash the brush roller with water and then leave it to dry.

Step 6. When it is completely dry, reconnect the brush roller to the vacuum cleaner and then put the brush cover back on.

Step 7. Turn your Shark rocket powerhead vacuum cleaner back on and check if it is working like it is supposed to now.

How to clean the brush roller of a Shark navigator lift away vacuum cleaner

Follow the steps below to clean the brush roller of your Shark navigator lift away vacuum cleaner . . .

Step 1. Ensure that your machine is turned off and unplugged from the power outlet before you begin the cleaning process. Cleaning any part of your Shark navigator lift away vacuum cleaner when the machine is turned on or plugged into the power outlet can cause electrocution.

Step 2. Flip the vacuum cleaner over to gain access to the brush head attachment.

Step 3. Get a flat head screwdriver and use it to take out the wheels at the bottom of the brush head attachment. Keep the wheels in a safe place.

Step 4. Get a Phillips head screwdriver and use it to take out the screws at the bottom of the vacuum cleaner holding the brush roller cover in place. Keep the screws in a safe place.

Step 5. Move the blue fulcrum between the brush head attachment and the main part of the vacuum cleaner back and forth to loosen the crevice between the brush roller enclosure.

Step 6.Get a flat head screwdriver and use it to pry the brush roller cover open. Take the brush roller cover out of the vacuum cleaner and set it aside.

Step 7. Take the brush roller out of the vacuum cleaner then slide it through the vacuum cleaner.

Step 8. Get a pair of scissors and use it to carefully cut off any hair or thread that may be on the brush roller. Take the hair or thread out of the brush roller and throw it away.

Step 9. When it is completely clean, reconnect the brush roller to the brush head attachment and then slide it through the vacuum belt again. Make sure to lock it in place properly.

Step 10. Reconnect the brush roller cover to the vacuum cleaner and make sure to lock it in place properly.

Step 11. Reconnect the screws that you removed from the brush roller cover earlier.

Step 12. Flip the vacuum cleaner over again.

Step 13. Turn your Shark navigator lift away vacuum cleaner back on and check if it is working like it is supposed to now.

Note: This replacement process also works for a Shark rotator lift away vacuum cleaner.

Shark Vacuum Cleaner Filter Smells – Why and How To Fix

If the filter of your Shark vacuum cleaner smells, the problem could be that vacuum filters are dirty. To solve the problem, you will need to clean the filters. After cleaning the filters of your Shark vacuum cleaner, they should stop emitting a foul odor.

Are Shark Robot Vacuum Cleaner Filters Washable?

No, your Shark robot vacuum cleaner does not come with a washable HEPA filter.

Can I Use My Shark Vacuum Cleaner Without A Filter?

No, your Shark vacuum cleaner won’t be able to function properly without its filters so you can’t use a Shark vacuum cleaner without a filter.

When To Replace Shark Vacuum Filter

i6You should replace the filter of your Shark once every 2 to 3 months or when the suction power of your machine has reduced.

Leave a Comment