Black And Decker Vacuum Turning Off [Problems & Solutions]

If your Black and Decker vacuum keeps turning off, this article is for you. Here we’ll identify the issue your Black and Decker vacuum has . . .

Black And Decker Handheld Vacuum Cleaner Keeps Shutting Off – Why and How To Fix

If your Black and Decker handheld vacuum cleaner keeps turning off, the machine could have one of two problems. Keep on reading to figure out and solve the problem your Black and Decker cordless vacuum cleaner has . . .

The vacuum battery is low

If the battery of your Black and Decker handheld vacuum cleaner is low, the machine won’t be able to work without shutting off continuously. To solve the problem, you will need to charge your vacuum cleaner. Follow the steps below to charge your Black and Decker cordless vacuum cleaner . . .

Step 1. Turn your vacuum cleaner off before you begin. Never charge your Black and Decker handheld vacuum cleaner when it is turned on.

Step 2. Plug your power cord into your power outlet and turn the power outlet on.

Step 3. Plug the power cord into your vacuum cleaner and leave it to charge for about five hours. You can tell that your Black and Decker vacuum cleaner is charging when you see the power indicator light flashing.

Step 4. Unplug the power cord from the vacuum cleaner once your machine is fully charged. You can tell that your Black and Decker handheld vacuum cleaner is fully charged when the power indicator light stops flashing.

Step 5. Turn your Black and Decker handheld vacuum cleaner back on and check if it is working like it is supposed to now.

The filter is dirty

If the filter of your Black and Decker handheld vacuum cleaner is dirty, the machine won’t be able to work without shutting off continuously. To solve the problem, you will need to clean the vacuum filter. Follow the steps below to clean the filters of two types of Black and Decker handheld vacuum cleaners . . .

black and decker vacuum filter

How to clean the filter of a Black and Decker handheld vacuum cleaner with a door

Follow the steps below to clean the filter of your Black and Decker handheld vacuum cleaner with a door properly . . .

Step 1. Turn your vacuum cleaner off and unplug it from the power outlet before you begin the cleaning process. Never clean any part of your Black and Decker handheld vacuum cleaner when it is turned on or plugged into your power outlet. Doing so can cause electrocution.

Step 2. Open the door of the vacuum cleaner to gain access to the vacuum canister.

Step 3. Empty the canister over a trash can.

Step 4. Press the button on the nozzle of the vacuum cleaner to disconnect the canister from the rest of the machine.

Step 5. Take the pleated filter out of the vacuum canister by pulling it firmly.

Step 6. Tap the pleated filter on the side of a trash can or sink to get rid of loose dirt.

Step 7. Wash the pleated filter with warm water and mild detergent. Leave the filter to dry.

Step 8. Make sure the filter is completely dry before reconnecting it to the vacuum canister.
Using your Black and Decker handheld vacuum cleaner with a wet filter can cause it to malfunction.

Step 9. Wipe the inside of the vacuum canister with a dry piece of cloth or tissue before reconnecting the pleated filter to it.

Step 10. Wash the vacuum canister with warm water and detergent. Leave the canister to dry.

Step 11. Reconnect the pleated filter to the vacuum canister when the canister is completely dry.

Step 12. Reconnect the vacuum canister to the vacuum cleaner again. You can tell that the canister is properly secured when you hear it lock with a click.

Step 13. Reconnect the nozzle to the vacuum cleaner.

Step 14. Turn your Black and Decker handheld vacuum cleaner back on and check if it is working like it is supposed to now..

How to clean the filters of a Black and Decker handheld vacuum cleaner with a nozzle

Follow the steps below to clean the filters of your Black and Decker handheld vacuum cleaner with a nozzle . . .

Step 1. Turn your vacuum cleaner off and unplug it from the power outlet before you begin the cleaning process. Never clean any part of your Black and Decker handheld vacuum cleaner when the machine turned on or plugged into your power outlet. Doing so can cause electrocution.

Step 2. Press the two tabs on the side of the vacuum nozzle to disconnect it from the vacuum cleaner and to gain access to the vacuum canister.

Step 3. Empty the canister over a trash can and tap the bottom of the vacuum cleaner to get rid of more stubborn dirt.

Step 4. Your Black and Decker handheld vacuum cleaner with a nozzle has a pre filter and a pleated filter. Press the release button on the handle of the vacuum cleaner to disconnect the vacuum canister from the rest of the machine and to gain access to the filters.

Step 5. Disconnect the filters from the vacuum cleaner and twist the pre filter clockwise to separate them.

Step 6. Tap the pre filter on the side of a trash can or sink to get rid of loose dirt.

Step 7. Brush the pleated filter with your hand to get rid of loose dirt.

Step 8. Wash the pre filter and pleated filter with warm water and a mild detergent then leave them to dry.

Step 9. Make sure the filters are completely dry before reconnecting them to the vacuum cleaner. Using your Black and Decker handheld vacuum cleaner with a wet pre filter or pleated filter can cause your machine to malfunction.

Step 10. Wash the vacuum canister with warm water and a mild detergent then leave it to dry.

Step 11. When the filters are completely dry, reattach them then reconnect them to the vacuum canister.

Step 12. Reconnect the vacuum canister to the vacuum cleaner.

Step 13. Reconnect the nozzle to the vacuum cleaner

Step 14. Turn your Black and Decker handheld vacuum cleaner back on and check if it is working like it is supposed to now.

Black and Decker Lithium Vacuum Cleaner Keeps Turning Off – Why and How To Fix


If your Black and decker lithium vacuum cleaner keeps turning off, the machine could have one of two problems Keep on reading to figure out and solve the problem your Black and Decker lithium vacuum cleaner might have

The vacuum cleaner is overheating

If your Black and Decker lithium vacuum cleaner is overheating, the machine won’t be able to work properly without turning off. A clogged motor can cause your Black and Decker vacuum cleaner to overheat. To solve the problem, you will need to clean the vacuum motor. Follow the steps below to clean your Black and Decker vacuum cleaner motor properly . . .

Step 1. Leave the vacuum cleaner to cool down for about thirty minutes before you begin.

Step 2. Turn the vacuum cleaner off and unplug it from the power outlet. Working on your Black and Decker lithium vacuum cleaner when it is turned on or plugged into the power outlet can cause electrocution.

Step 3. Use a Phillips head screwdriver to remove the screws holding the motor cover in place. You might find the motor cover behind the vacuum cleaner . Keep the screws that you removed in a safe place.

Step 4. Take the motor cover out and set it aside.

Step 5. Remove the screws holding the motor in place and keep them in a safe place.

Step 6. There might be wires holding the motor in place. Disconnect the wires and take the motor out of the vacuum cleaner.

Step 7. Use a dry piece of cloth or tissue or a soft brush to clean out dust in the motor.

Step 8. Remove the object that is blocking the motor from the motor chamber.

Step 9. Wipe the motor with a dry piece of cloth or tissue.

Step 10. When the motor is completely clean, reconnect it to the vacuum cleaner and use the wires that you disconnected earlier to hold it in place.

Step 11. Put the screws that you removed before back in their places.

Step 12. Put the motor cover back on then put the screws that you removed earlier back in their places.

Step 13. Turn your Black and Decker lithium vacuum cleaner back on and check if it is working like it is supposed to now.

The vacuum motor is bad

If the motor of your Black and Decker vacuum cleaner is bad, the machine won’t be able to work without going off. To solve the problem, you will need to replace the vacuum motor. Follow the steps below to replace your Black and Decker lithium vacuum cleaner motor properly . . .

Step 1. Turn your vacuum cleaner cleaner off and unplug it from the power outlet before you begin. Never work on your Black and Decker lithium vacuum cleaner when it is turned on or plugged into your power outlet. Doing so can be very dangerous.

Step 2. Locate the motor cover. You might find it at the back of the vacuum cleaner.

Step 3. Use a Phillips head screwdriver to take out the screws holding the motor cover in place. Keep the screws in a safe place.

Step 4. Take the motor cover out of the vacuum cleaner and set it aside.

Step 5. Use the screwdriver to take out the screws holding the motor in place. Keep the screws in a safe place.

Step 6. There might be wires holding the motor in place. Disconnect them then take the old motor out of the vacuum cleaner .

Step 7. Put a new Black and Decker lithium vacuum cleaner motor in the place of the old one.

Step 8. Reconnect the wires that you disconnected earlier.

Step 9.Use the screws that you removed earlier to hold the new vacuum motor in place.

Step 10. Put the motor cover back on and put the screws back in their places.

Step 11. Turn your Black and Decker lithium vacuum cleaner back and check if it is working like it is supposed to now.

Leave a Comment