Hoover Vacuum Cleaner Filter [Problems, Solutions and Guide]

If your Hoover vacuum cleaner filter has any problems, you’re in the right place. Here we will identify the issue your Hoover vacuum has . . .

Table of Contents

How To Clean Hoover Central Vacuum Cleaner Filter

Follow the steps below to clean the filter of a Hoover central vacuum cleaner . . .

Step 1. Ensure that your machine is turned off and unplugged from your power outlet before you start the cleaning process. Cleaning the filter of your Hoover central vacuum cleaner when the machine is plugged into the power outlet can cause electrocution.

Step 2. Unhook the latch on the side of the vacuum cleaner to disconnect the bottom part of the machine from the rest of the vacuum cleaner. Take the bottom part of the vacuum cleaner out and then set it aside.

Step 3. Take the cloth filter out of the vacuum cleaner and then set the rest of the machine aside.

Step 4. Shake the cloth filter to get rid of loose dust and dirt.

Step 5. When it is completely clean, reconnect the cloth filter to the vacuum cleaner. Make sure to lock the filter in place properly.

Step 6. Take the vacuum canister out of the vacuum cleaner and then empty it over a trash can. Wipe the internal part of the canister with a dry piece of cloth or tissue.

Step 7. Take the foam filter out of the vacuum cleaner. Set the rest of your machine aside.

Step 8. Wash the foam filter with water and no detergent then leave it to dry. Make sure the filter is completely dry before reconnecting it to the vacuum cleaner . Using your Hoover central vacuum cleaner with a wet filter can cause it to malfunction.

Step 9. When it is completely dry, reconnect the foam filter to the vacuum cleaner and make sure to lock it in place properly.

Step 10. Reconnect the vacuum canister to the vacuum cleaner.

Step 11. Reconnect the bottom part of the vacuum cleaner to the rest of the machine and make sure to use the latches to lock it in place properly.

Step 12. Turn your Hoover central vacuum cleaner back on and you can start cleaning with it again.

How To Clean Hoover Blade Cordless Vacuum Cleaner Filter

Follow the steps below to clean the filter of your Hoover blade cordless vacuum cleaner filter . . .

Step 1. Make sure your vacuum cleaner is turned off and unplugged from the power outlet before you begin the cleaning process.

Step 2. Disconnect the vacuum canister from the vacuum cleaner. Set the rest of your vacuum cleaner aside.

Step 3. Open the lid of the vacuum canister then empty it over a trash can.

Step 4. If necessary, wipe the internal part of the vacuum canister with a dry piece of cloth or tissue.

Step 5. Take the filter out of the vacuum canister and then set the rest of the canister aside.

Step 6. Tap the filter on the side of the trash can or sink to get rid of loose dirt.

Step 7. Wash the filter with water and a mild detergent and then leave it to dry. Make sure the filter is completely dry before reconnecting it to the vacuum cleaner. Using your Hoover blade cordless vacuum cleaner with a wet filter can cause it to malfunction.

Step 8. When it is completely dry, reconnect the filter to the vacuum canister. Make sure to lock the filter in place properly.

Step 9. Close the lid of the vacuum canister then reconnect it to the vacuum cleaner.

Step 10. Turn your Hoover blade cordless vacuum cleaner back on and start cleaning with it again.

How To Clean Hoover Windtunnel Vacuum Cleaner Filter

Follow the steps below to clean the filters of different kinds of Hoover windtunnel vacuum cleaners . . .

How to clean the filter of a Hoover Windtunnel air bagless upright vacuum cleaner

Follow the steps below to clean the filter of your Hoover windtunnel air bagless upright vacuum cleaner properly . . .

Step 1. Turn your vacuum cleaner off and unplug it from the power outlet before you begin the cleaning process. Cleaning any part of your Hoover windtunnel air bagless upright vacuum cleaner when the machine is turned on or plugged into the power outlet can cause electrocution.

Step 2. To gain access to the vacuum filter, you will need to disconnect the vacuum canister from the rest of the machine.

Press the button on the handle of the vacuum cleaner canister then pull it to separate it from the rest of the machine. Set the rest of the vacuum cleaner aside.

Step 3. Twist the cover of the vacuum canister to open it. Set the vacuum canister cover aside.

Step 4. Take the filter out of the vacuum cleaner canister. Set the vacuum canister aide.

Step 5. Tap the filter on the side of a trash can or sink to get rid of loose dust and dirt.

Step 6. Wash the filter with water and no detergent then leave it to dry. Make sure the filter is completely dry before reconnecting it to the vacuum cleaner canister. Using your Hoover windtunnel air bagless upright vacuum cleaner with a wet filter can cause it to malfunction.

Step 7. When it is completely dry, reconnect the filter to the vacuum canister.

Step 8. Reconnect the canister lid to the vacuum canister then twist the lid to lock it in place again.

Step 9. In the vacuum canister chamber, you will see a filter case. Take the filter case out of the vacuum cleaner. Set the rest of your vacuum cleaner aside.

Step 10. Take the filter out of the filter casing then set the case aside.

Step 11. Tap the filter on the side of a trash can or sink to clean it. The second filter can’t be washed with water or detergent.

Step 12. When it is completely clean, reconnect the second filter to the filter casing.

Step 13. Reconnect the filter and the filter case to the vacuum canister chamber.

Step 14. Reconnect the vacuum canister to the vacuum cleaner and make sure to lock it in place properly.

Step 15. Turn your Hoover windtunnel air bagless upright vacuum cleaner back on and you can start cleaning with it again.

How to clean the filters of a Hoover windtunnel 2 rewind bagless upright vacuum cleaner

Follow the steps below to clean the filters of your Hoover windtunnel 2 rewind bagless upright vacuum cleaner . . .

Step 1. Make sure your Hoover vacuum cleaner is turned off and unplugged from the power outlet before you start the cleaning process.

Step 2. Disconnect the vacuum canister from the vacuum cleaner to gain access to the first filter. Set the rest of your vacuum cleaner aside.

Step 3. Open the lid of the vacuum canister then lean it backwards.

Step 4. Take the first filter out of the vacuum canister. Set the rest of the vacuum canister aside.

Step 5. Tap the filter on the side of a trash can or sink to get rid of loose dirt.

Step 6. Wash the filter with water and no detergent then leave it to dry. Make sure the filter is completely dry before connecting it to the vacuum cleaner. Using your Hoover windtunnel 2 rewind bagless upright vacuum cleaner with a wet filter can cause it to malfunction.

Step 7. When it is completely dry, reconnect the filter to the vacuum canister.

Step 8. Closer the lid of the vacuum canister then reconnect it to the vacuum cleaner. Make sure to lock the vacuum canister in place properly.

Step 9. At the bottom of the vacuum canister, you will see a filter case. Take the filter case out of the vacuum cleaner then set the rest of your machine aside.

Step 10. Tap the filter on the side of a trash can or sink to clean it. The second filter of your Hoover windtunnel 2 rewind bagless upright vacuum cleaner can’t be cleaned with water or detergent.

Step 11. When it is completely clean, reconnect the filter to the bottom of the vacuum cleaner and make sure to lock it in place properly.

Step 12. Turn your Hoover windtunnel 2 rewind bagless upright vacuum cleaner back on and you can start cleaning with it again.

hoover vacuum cleaner filter

How To Clean Hoover Windtunnel Vacuum Cleaner Filter

Follow the steps below to clean the filter of your Hoover Windtunnel vacuum cleaner . . .

Step 1. Ensure that your machine is turned off and unplugged from the power outlet before you begin the cleaning process. Cleaning any part of your Hoover fusion vacuum cleaner when the machine is turned on or plugged into the power outlet can cause electrocution.

Step 2. Press the button on the handle of the vacuum canister to disconnect it from the rest of the vacuum cleaner.

Step 3. Separate the vacuum canister from the vacuum cleaner. Set the rest of your vacuum cleaner aside.

Step 4. Open the lid of the vacuum canister to gain access to the outer filter.

Step 5. Take the outer filter out of the vacuum canister then set the rest of the canister aside.

Step 6. Tape the outer filter on the side of a trash can or sink to get rid of loose dust and debris.

Step 7. Wash the filter with water and no detergent then leave it to dry. Make sure the filter is completely dry before reconnecting it to the vacuum cleaner. Using your Hoover windtunnel vacuum cleaner with a wet filter can cause it to malfunction.

Step 8. Close the lid of the vacuum canister again then pull it to take the inner filter out of the canister. Set the rest of the vacuum canister aside.

Step 9. Open the vacuum canister lid then get a screwdriver and use it to take out the screws holding the lid in place. Keep the screws in a safe place.

Step 10. Separate the inner filter from the vacuum canister cover. Set the vacuum canister cover aside.

Step 11. Tap the inner filter on the side of a trash can or sink to get rid of loose dirt.

Step 12. Wash the inner filler with water and no detergent then leave it to dry.

Step 13. When it is completely dry, reconnect the inner filter to the vacuum canister cover then use the screws that you removed earlier to lock it in place properly.

Step 14. Open the vacuum canister lid then reconnect the outer filter to it. Make sure to lock the outer filter in place properly.

Step 15. Reconnect the inner and the outer filter to the vacuum canister and make sure to lock them in place properly.

Step 16. Reconnect the vacuum caister to the vacuum cleaner and make sure to lock it in place properly.

Step 17.Turn your Hoover windtunnel vacuum cleaner back on and you can start cleaning with it again.

How To Clean Hoover Fusion Vacuum Cleaner Filter

Follow the steps below to clean the filter of a Hoover fusion vacuum cleaner . . .

Step 1. Make sure your Hoover vacuum cleaner is turned off and unplugged from the power outlet before you begin the cleaning process.

Step 2. Press the button on the handle of the vacuum canister to disconnect it from the vacuum cleaner.

Step 3. Separate the vacuum canister from the vacuum cleaner. Set the rest of your vacuum cleaner aside.

Step 4. Pull the lid of the vacuum canister to take the big filter out of the rest of the canister. Set the rest of the vacuum canister aside.

Step 5. Get a dry piece of cloth or tissue or a soft brush and use it to wipe off any dust or dirt that may be stuck on the vacuum cleaner filter.

Step 6. When it is completely clean, reconnect the big filter to the vacuum canister.

Step 7. In the vacuum canister chamber, you will see a smaller filter. Take the filter out of the canister chamber. Set the rest of the vacuum cleaner aside.

Step 8. Tap the smaller filter on the side of a trash can or sink to get rid of loose dirt.

Step 9. Wash the filter with water and no detergent then leave it to dry. Make sure the filter is completely dry before reconnecting it to the vacuum cleaner. Using your Hoover fusion vacuum cleaner with a wet filter can cause it to malfunction.

Step 10. When it is completely dry, reconnect the small filter to the canister chamber.

Step 11. Reconnect the vacuum canister to the vacuum cleaner and make sure to lock it in place properly

Step 12. Turn your Hoover fusion vacuum cleaner back on and you can start cleaning with it again.

How To Clean Hoover Pet Vacuum Cleaner Filter

Follow the steps below to clean the filters of different kinds of Hoover pet vacuum cleaner filters properly . . .

How to clean the filter of a Hoover reactive pet vacuum cleaner

Follow the steps below to clean the filter of your Hoover reactive pet vacuum cleaner . . .

Step 1. Ensure that your machine is turned off and unplugged from the power outlet before you start the cleaning process. Cleaning the filter of your Hoover reactive pet vacuum cleaner when the machine is turned on or plugged into the power outlet can cause electrocution.

Step 2. Press the button on the handle of the vacuum canister to disconnect it from the rest of the vacuum cleaner.

Step 3. Separate the vacuum canister from the vacuum cleaner. Set the vacuum cleaner canister aside.

Step 4. At the bottom of the vacuum cleaner, you will see a filter case. Take the filter and the filter case out of the vacuum cleaner. Set the rest of the vacuum cleaner aside.

Step 5.Tap the filter and the filter casing on the side of a trash can or sink to clean it. This filter cannot be cleaned with water or detergent.

Step 6. When it is completely clean, reconnect the filter and filter case to the bottom of the vacuum cleaner and make sure to lock it in place properly.

Step 7. Open the lid of the vacuum canister to gain access to the other two filters. Empty the canister over a trash can.

Step 8. Take the foam filter out of the lid of the vacuum canister. Set the vacuum canister aside.

Step 9. Wash the filter with water and no detergent then leave it to dry. Make sure the filter is completely dry before reconnecting it to the vacuum canister. Using your Hoover reactive pet vacuum cleaner with a wet filter can cause it to malfunction.

Step 10. When it is completely dry, reconnect the foam filter to the lid of the vacuum canister.

Step 11. You will see the third filter inside the vacuum canister. Take the third filter out of the vacuum canister then set the rest of the canister aside.

Step 12. Tap the filter on the side of a trash can or sink to clean it. This filter can not be cleaned with water or detergent.

Step 13. When it is completely clean, reconnect the third filter to the vacuum canister and make sure to lock it in place properly.

Step 14. Close the lid of the vacuum canister then reconnect it to the vacuum cleaner and make sure to lock it in place properly.

Step 15. Turn your Hoover reactive pet vacuum cleaner back on and you can start cleaning with it again.

How to clean the filter of a Hoover rush pet vacuum cleaner

Follow the steps below to clean the filters of your Hoover rush pet vacuum cleaner . . .

Step 1. Make sure your Hoover vacuum cleaner is turned off and unplugged from the power outlet before you begin the cleaning process.

Step 2. Press the button on the handle of the vacuum canister to disconnect it from the vacuum cleaner. Set the vacuum cleaner canister aside.

Step 3. Turn the vacuum cleaner backwards to gain access to the first filter.

Step 4. Take the filter cover at the back of the vacuum cleaner out and set it aside.

Step 5. Take the first filter out of the vacuum cleaner. Set the rest of your vacuum cleaner aside.

Step 6. Open the lid of the vacuum canister to gain access to the second filter.

Step 7. Take the second filter out of the vacuum canister cover. Set the canister cover aside.

Step 8. Take the foam filter out of the outer filter.

Step 9. Tap at the filters on the side of a trash can or sink to get rid of loose dust and debris.

Step 10. Wash all the filters with water and no detergent then leave them to dry. Make sure the filters are completely dry before reconnecting them to the vacuum canister. Using your Hoover rush pet vacuum cleaner with wet filters can cause it to malfunction.

Step 11. When they are completely dry, reattach the foam filter and outer filter.

Step 12. Reconnect the foam filter and the outer filter out the vacuum canister cover.

Step 13. Reconnect the canister cover to the vacuum canister. Make sure to lock the canister cover in place properly.

Step 14. Reconnect the first filter to the back of the vacuum cleaner and make sure to lock it in place properly.

Step 15. Reconnect the filter cover to the back of the vacuum cleaner.

Step 16. Reconnect the vacuum canister to the vacuum cleaner and make sure to lock it in place properly.

Step 17. Turn your Hoover rush pet vacuum cleaner back on and you can start cleaning with it again.

How to clean the filter of a Hoover hurricane pet vacuum cleaner

Follow the steps below to clean the filter of your Hoover hurricane pet vacuum cleaner . . .

Step 1. Make sure the vacuum cleaner is turned off and unplugged from the power outlet before you start the cleaning process. Cleaning the filters of your Hoover hurricane pet vacuum cleaner when the machine is turned on or plugged into the power outlet can cause electrocution.

Step 2. Press the button at the back of the vacuum canister to disconnect it from the rest of the vacuum cleaner. Set the vacuum canister aside.

Step 3. Take the first filter out of the vacuum canister chamber and then set it aside.

Step 4. Open the lid of the vacuum canister to gain access to the second filter and the third filter. Empty the vacuum canister over a trash can.

Step 5. Take the second filter out of the vacuum canister lid. Set the canister cover aside.

Step 6. Separate the long filter from the third filter and set them aside.

Step 7. Tap the first filter on the side of a trash can or sink to get rid of loose dust and debris.

Step 8. Wash the filter with water and no detergent then leave it to dry. Make sure the filter is completely dry before reconnecting it to the vacuum cleaner. Using your Hoover hurricane pet vacuum cleaner with a wet filter can cause it to malfunction.

Step 9. When it is completely dry, reconnect the first filter to the vacuum canister chamber. Make sure to lock the filter in place properly.

Step 10. Tap the other two filters on the side of a trash can or sink to get rid of loose dirt.

Step 11. Wash the two filters with water and no detergent then leave them to dry.

Step 12. When they are completely dry, reattach the two filters then reconnect them to the vacuum canister lid. Make sure to lock the filters in place properly.

Step 13. Close the lid of the vacuum canister then reconnect it to the vacuum cleaner. Make sure to lock it in place properly.

Step 14. Turn your Hoover hurricane pet vacuum cleaner back on and you can start cleaning with it again.

How To Clean Hoover Stick Vacuum Cleaner Filter

Follow the steps below to clean the filters of different kinds of Hoover stick vacuum cleaner . . .

How to clean the filter of a Hoover sprint stick cordless vacuum cleaner

Follow the steps below to clean the filters of your Hoover sprint stick cordless vacuum cleaner properly . . .

Step 1. Always remember to turn your vacuum cleaner off and unplug it from the power outlet before you begin the cleaning process.

Step 2. Disconnect the vacuum canister from the vacuum cleaner to gain access to the two filters. Set the rest of the vacuum cleaner aside.

Step 3. Open the lid of the vacuum canister and then empty it over a trash can.

Step 4. Twist the first filter counter clockwise to take it out of the vacuum canister. Set the vacuum canister aside.

Step 5. Tap the first filter on the side of a trash can or sink to get rid of loose dust and debris.

Step 6. Wash the filter with water and no detergent then leave it to dry. Make sure the filter is completely dry before reconnecting it to the vacuum cleaner. Using your Hoover sprint stick cordless vacuum cleaner with a wet filter can cause it to malfunction.

Step 7. Take the second filter out of the vacuum canister by twisting it counter clockwise. Set the vacuum canister aside.

Step 8. Wash the second filter with water and no detergent then leave it to dry.

Step 9. When they completely dry, reconnect the filters to the vacuum canister and turn them clockwise to lock them in place properly.

Step 10. Close the lid of the vacuum canister then reconnect it to the vacuum cleaner.\Make sure to lock it in place properly.

Step 11. Turn your Hoover sprint stick cordless vacuum cleaner back on and you can start cleaning with it again.

How to clean the filter of a Hoover freedom stick vacuum cleaner

Follow the steps below to clean the filter of your Hoover freedom stick vacuum cleaner . . .

Step 1. Turn your machine off and unplug it from the power outlet before you begin the cleaning process. Cleaning any part of your Hoover freedom stick vacuum cleaner when the machine is turned on or plugged into the power outlet can cause electrocution.

Step 2. Disconnect the vacuum hose from the vacuum cleaner. Set the vacuum hose aside.

Step 3. Flip the vacuum cleaner over.

Step 4. Press the button at the bottom of the vacuum cleaner to disconnect the vacuum canister from the rest of the machine.

Step 5. Take the vacuum canister out of the vacuum cleaner then set it aside.

Step 6. Twist the mesh filter anti clockwise to disconnect it from the main body of the vacuum cleaner. Separate the mesh filter from the vacuum cleaner then set the rest of your machine aside.

Step 7. Separate the mesh filter from the second filter.

Step 8. Tap the filters on the side of a trash can or sink to get rid of loose dirt.

Step 9. Wash the first filter with water and no detergent then leave it to dry. Make sure the filter is completely dry before reconnecting it to the vacuum cleaner. Using your Hoover freedom stick vacuum cleaner with a wet filter can cause it to malfunction.

Step 10. Wipe the second filter with a dry piece of cloth or tissue to clean it. This filter can not be washed with water or detergent.

Step 11. When they are completely dry, reattach the filters then reconnect them to the main body of the vacuum cleaner. Twist the filters to lock them in place properly.

Step 12. Reconnect the vacuum canister to the vacuum cleaner and make sure to lock it in place properly.

Step 13. Reconnect the vacuum hose to the vacuum cleaner.

Step 14. Turn your Hoover freedom stick vacuum ccleaner back on and you can start cleaning with it again.

How to clean the filter of a Hoover unplugged cordless stick vacuum cleaner

Follow the steps below to clean the filter of your Hoover unplugged cordless stick vacuum cleaner . . .

Step 1. Ensure that your machine is turned off and unplugged from the power before you start the cleaning process.

Step 2. Press the button at the bottom of the vacuum canister to disconnect it from the vacuum cleaner. See the rest of the vacuum cleaner aside.

Step 3. Take the inner and the outer filter out of the vacuum canister. Empty the vacuum canister then set it aside.

Step 4. Twist the inner filter to separate it from the outer filter.

Step 5. Tap the two filters on the side of a trash can or sink to get rid of loose dirt.

Step 6. Wash the filters with water and no detergent then leave them to dry. Make sure the filters are completely dry before reconnecting them to the vacuum cleaner.

Step 7. When they are completely dry, reattach the filters then reconnect them to the vacuum canister.

Step 8. Reconnect the vacuum canister to the vacuum cleaner and make sure to lock it in place properly.

Step 9. Turn your Hoover unplugged cordless stick vacuum cleaner back on and you can start cleaning with it again.

How to clean the filter of a Hoover 14 4v free motion handstick vacuum cleaner

Follow the steps below to clean the filter of your Hoover 14 4v free motion handstick vacuum cleaner . . .

Step 1. Turn your vacuum cleaner off and unplug it from the power outlet before you start. Cleaning any part of your Hoover 14 4v free motion handstick vacuum cleaner when the machine is turned on or plugged into the power outlet can cause electrocution.

Step 2. Press the button above the vacuum canister to disconnect it from the vacuum cleaner. Set the rest of the vacuum cleaner aside.

Step 3. Disconnect the lid of the vacuum canister from the rest of the container. Set the vacuum canister cover aside.

Step 4. Take the filter out of the vacuum canister. Set the rest of the vacuum canister aside.

Step 5. Tap the filter on the side of a trash can or sink to get rid of loose dirt.

Step 6. Wash the filter with water and no detergent then leave it to dry. Make sure the filter is completely dry before reconnecting it to the vacuum cleaner. Using your Hoover 14 4v free motion handstick vacuum cleaner with a wet filter can cause it to malfunction.

Step 7. When it is completely dry, reconnect the filter to the vacuum canister.

Step 8. Close the lid of the vacuum canister then reconnect it to the vacuum cleaner. Make sure to lock the canister in place properly.

Step 9. Turn your Hoover 14 4v free motion handstick vacuum cleaner back on and you can start cleaning with it again.

How to clean the filter of a Hoover 22v freedom plus vacuum cleaner

Follow the steps below to clean the filter of your Hoover 22v freedom plus vacuum cleaner . . .

Step 1. Turn your machine off and unplug it from the power outlet before you start the cleaning process.

Step 2. Flip the vacuum cleaner over.

Step 3. Empty the vacuum canister and then disconnect it from the vacuum cleaner. Set the vacuum canister aside.

Step 4. Take the first filter from the bottom of the vacuum cleaner. Set the vacuum filter aside.

Step 5. Flip the vacuum cleaner over again and turn it backwards.

Step 6. Press the button at the back of the vacuum cleaner to disconnect the casing of the second filter from the rest of the machine.

Step 7. Take the filter out of the vacuum cleaner. Set the rest of the vacuum cleaner aside.

Step 8. Separate the filter from the filter casing. Set the filter casing aside.

Step 9. Tap the two filters on the side of a trash can or sink to get rid of loose dust and debris.

Step 10. Wash the filters with water and no detergent then leave them to dry. Make sure the filters are completely dry before reconnecting them to the vacuum cleaner. Using your Hoover 22v freedom plus vacuum cleaner with wet filters can cause it to malfunction.

Step 11. When it is completely dry, reconnect the first filter to the bottom of the vacuum cleaner.

Step 12. Reconnect the vacuum canister to the vacuum cleaner and make sure to lock it in place properly.

Step 13. Reconnect the second filter to the filter casing then reconnect the case to the back of the vacuum cleaner.

Step 14. Turn your Hoover 22v freedom plus vacuum cleaner back on and you can start cleaning with it again.

How To Change Hoover Vacuum Cleaner Filter

Follow the steps below to change the filters of different kinds of Hoover vacuum cleaners . . .

How to change the filter of a Hoover central vacuum cleaner

Follow the steps below to change the filter of your Hoover central vacuum cleaner . . .

Step 1. Turn your machine off and unplug it from the power outlet before you begin the replacement process. Replacing any part of your Hoover central vacuum cleaner when the machine is turned on or plugged into the power outlet can cause electrocution.

Step 2. Unhook the latch on the side of the vacuum cleaner to disconnect the bottom of the part of the machine from the rest of the vacuum cleaner. Set the bottom part of the vacuum cleaner aside.

Step 3. Take the cloth filter out of the vacuum cleaner. Set the filter aside.

Step 4. Get a new Hoover central vacuum cleaner filter of the same kind and put it in the place of the old one.

Step 5. Take the vacuum canister out of the vacuum cleaner then set it aside.

Step 6. Take the foam filter out of the vacuum cleaner. Set the foam filter aside.

Step 7. Get a new Hoover vacuum cleaner filter of the same kind and put it in the place of the old one.

Step 8. Reconnect the vacuum canister to the vacuum cleaner.

Step 9. Reconnect the bottom part of the vacuum cleaner to the main body of the machine and then use the latch to lock it in place properly.

Step 10. Turn your Hoover central vacuum cleaner back on and you can start cleaning with it again.

How to replace the filter of a Hoover blade cordless vacuum cleaner

Follow the steps below to replace the filter of your Hoover blade cordless vacuum cleaner . . .

Step 1. Turn your vacuum cleaner off and unplug it from the vacuum cleaner before you start.

Step 2. Disconnect the vacuum canister from the vacuum cleaner. Set the rest of your vacuum cleaner aside.

Step 3. Open the lid of the vacuum canister and empty it over a trash can.

Step 4. Take the filter out of the vacuum canister and set it aside.

Step 5. Get a new Hoover vacuum cleaner filter of the same kind and put it in the place of the old one.

Step 6. Close the lid of the vacuum canister then reconnect it to the vacuum cleaner. |Make sure to lock the canister in place properly.

Step 7. Turn your Hoover blade cordless vacuum cleaner back on and you can start cleaning with it again.

How to replace the filter of a Hoover windtunnel air bagless upright vacuum cleaner

Follow the steps below to replace the filter of your Hoover windtunnel air bagless upright vacuum cleaner . . .

Step 1. Make sure your vacuum cleaner is turned off and unplugged from the power outlet before you start the replacement process.

Step 2. Press the button on the handle of the vacuum canister to disconnect it from the vacuum cleaner.

Step 3. Separate the vacuum canister from the vacuum cleaner. Set the rest of the vacuum cleaner aside.

Step 4. Twist the cover of the vacuum canister to open it. Set the vacuum canister cover aside.

Step 5. Take the filter out of the vacuum canister then set it aside.

Step 6. Get a new Hoover windtunnel vacuum cleaner filter of the same kind and put it in the place of the old one.

Step 7. Close the lid of the vacuum canister and twist it to lock it in place properly.

Step 8. In the vacuum canister chamber, you will see another filter. Take the filter out of the vacuum cleaner then take it out of the filter casing. Set the old filter aside.

Step 9. Get a new Hoover vacuum cleaner of the same kind and connect it to the filter casing.

Step 10. Reconnect the filter casing to the vacuum cleaner and make sure to lock it in place properly.

Step 11. Reconnect the vacuum canister to the vacuum cleaner.

Step 12. Turn your Hoover windtunnel air bagless upright vacuum cleaner back on and you can start cleaning with it again.

How to replace the filter of a Hoover windtunnel 2 rewind bagless upright vacuum cleaner

Follow the steps below to replace the filter of your HOover windtunnel 2 rewind bagless upright vacuum cleaner. . .

Step 1. Turn your vacuum cleaner off and unplug it from the power outlet before you start.

Step 2. Disconnect the vacuum canister from the vacuum cleaner to gain access to the first filter. Set the rest of your vacuum cleaner aside.

Step 3. Open the lid of the vacuum canister and then lean it backwards.

Step 4. Take the first filter out of the vacuum cleaner canister and set it aside.

Step 5. Get a new Hoover windtunnel vacuum cleaner filter and put it in the place of the old one.

Step 6. Close the vacuum canister then reconnect it to the vacuum cleaner.

Step 7. At the bottom of the vacuum canister, you will see another filter. Take the filter out of the vacuum cleaner and set it aside.

Step 8. Get a new Hoover vacuum cleaner filter of the chase kind and put it in the place of the old one. Make sure to lock the new filter in place properly.

Step 9. Turn your Hoover windtunnel 2 rewind air bagless upright vacuum cleaner back on and you can start cleaning with it again.

How to replace the filter of a Hoover windtunnel vacuum cleaner

Followthe steps below to replace the filter of your Hoover windtunnel vacuum cleaner . . .

Step 1. Ensure that your machine is turned off and unplugged from the power outlet before you begin. Replacing any part of your Hoover windtunnel vacuum cleaner when the machine is turned on or plugged into the power outlet can cause electrocution.

Step 2. Press the button on the handle of the vacuum canister to disconnect it from the rest of the machine.

Step 3. Take the vacuum canister out of the vacuum cleaner. Set the rest of the vacuum cleaner aside.

Step 4. Open the lid of the vacuum canister to gain access to the outer filter.

Step 5. Take the outer filter out of the vacuum cleaner canister and set it aside.

Step 6. Get a new Hoover windtunnel vacuum cleaner filter and put it in the place of the old one.

Step 7. Close the lid of the vacuum canister again and then take the inner filter out of the canister.

Step 8. Open the lid of the vacuum canister and get a screwdriver and use it to take out the screws holding the vacuum canister cover in place. Keep the screws in a safe place.

Step 9. Separate the inner filter from the vacuum canister cover. Set the inner filter aside.

Step 10. Get a new Hoover windtunnel vacuum cleaner filter and reconnect it to the vacuum canister cover and use the screws that you removed earlier to lock it in place again.

Step 11. Reconnect the vacuum canister cover to the vacuum canister.

Step 12. Reconnect the vacuum canister to the vacuum cleaner.

Step 13. Turn your Hoover windtunnel vacuum cleaner back on and you can start cleaning with it again.

How to replace the filters of a Hoover fusion vacuum cleaner

Follow the steps below to replace the filter of your Hoover fusion vacuum cleaner . . .

Step 1. Make sure your vacuum cleaner is turned off and unplugged from the power outlet before you begin.

Step 2. Press the button on the handle of the vacuum canister to disconnect it from the rest of the machine.

Step 3. Separate the vacuum canister from the vacuum cleaner. Set the rest of the vacuum cleaner aside.

Step 4. Open the lid of the vacuum canister then set it aside.

Step 5. Take the big filter out of the vacuum cleaner and then set it aside.

Step 6. Get a new Shark vacuum cleaner filter of the same kind and put it in the place of the oil one.

Step 7. In the vacuum canister chamber, you will see a smaller filter. Take the filter out of the vacuum canister chamber and then set it aside.

Step 8. Get a new Hoover fusion vacuum cleaner filter and put it in the place of the old one.

Step 9. Reconnect the vacuum canister to the vacuum cleaner and make sure to lock it in place properly.

Step 10. Turn your Hoover fusion vacuum cleaner back on and you can start cleaning with it again.

How to replace the filter of a Hoover reactive pet vacuum cleaner

Follow the steps below to change the filter of your Hoover reactive pet vacuum c;leaner . . .

Step 1. Make sure your vacuum cleaner is turned off and unplugged from the power outlet before you begin the replacement process. Replacing any part of your Hoover reactive pet vacuum cleaner when the machine is turned on or plugged into the power outlet can cause electrocution.

Step 2. Press the button on the handle of the vacuum canister to disconnect it from the rest of your machine.

Step 3. Separate the vacuum canister from the rest of the vacuum cleanser. Set the rest of your vacuum cleaner aside.

Step 4. At the bottom of the vacuum cleaner, you will see a filter casing. Take the filter and the filter casing out of the vacuum cleaner and set them aside.

Step 5. Get a new Hoover reactive pet vacuum cleaner filter of the same kind and put it in the place of the old one.

Step 6. Open the lid of the vacuum canister to gain access to the other two filters.

Step 7. Take the foam filter out of the vacuum canister lid and set it aside.

Step 8. Get a new Hoover reactive pet vacuum cleaner filter and put it in the place of the old one.

Step 9. Take the third and last filter out of the vacuum canister and set it aside.

Step 10. Get a new Hoover pet vacuum cleaner filter of the same kind and put in the place of the old one. Make sure to lock the new filter in place properly.

Step 11. Close the lid of the vacuum canister and then reconnect it to the vacuum cleaner. Make sure to lock the vacuum canister in place properly.

Step 12. Turn your Hoover reactive pet vacuum cleaner back on and you can start cleaning with it again.

How to replace the filter of a Hoover rush pet vacuum cleaner

Follow the steps below to change the filter of your Hoover rush pet vacuum cleaner properly . . .

Step 1. Ensure that your machine is turned off and unplugged from the power outlet before you start. Replacing any part of your Hoover rush pet vacuum cleaner when the machine is turned on or plugged into the power outlet can cause electrocution.

Step 2. Press the button on the handle of the vacuum canister to disconnect it from the rest of the vacuum cleaner.

Step 3. Take the vacuum canister out of the vacuum cleaner. Set the vacuum cleaner canister aside.

Step 4. Turn the vacuum cleaner backwards to gain access to the first filter.

Step 5. Take the filter cover out of the vacuum cleaner and then set it aside.

Step 6. Take the first filter out of the vacuum cleaner and set it aside.

Step 7. Get a new Hoover rush pet vacuum cleaner filter and put it in the place of the old one.

Step 8. Open the lid of the vacuum canister to gain access to the second filter.

Step 9. Take the second filter out of the vacuum canister cover and then set it aside.

Step 10. Get a new Hoover rush pet vacuum cleaner filter and put it in the place of the old one.
Make sure to lock the new filter in place properly.

Step 11. Close the lid of the vacuum canister and then reconnect it to the vacuum ccleaner.
Make sure to lock the vacuum canister in place properly.

Step 12. Turn your Hoover rush pet vacuum cleaner back on and you can start cleaning with it aain.

How to change the filter of a Hoover hurricane pet vacuum cleaner

Follow the steps below to change the filter of your Hoover hurricane pet vacuum cleaner . . .

Step 1. Make sure your Hoover vacuum cleaner is turned off and unplugged from the power outlet before you start the replacement process.

Step 2. Press the button at the back of the vacuum canister to disconnect it from the rest of the vacuum cleaner.

Step 3. Take the vacuum canister out of the vacuum cleaner and then set it aside.

Step 4. Take the first filter out of the vacuum canister chamber and then set it aside.

Step 5. Get a new Hoover hurricane pet vacuum cleaner filter and put in the place of the old one. Make sure to lock the new filter in place properly.

Step 6. Open the lid of the vacuum canister to gain access to the second filter and then third filter. Empty the vacuum canister over a trash can.

Step 7. Take the second filter and the third filter out of the vacuum canister cover and then set them aside.

Step 8. Get new Hoover hurricane pet vacuum cleaner filters of the same kind and put it in the place of the old one. Make sure to lock the new filters in place properly.

Step 9. Close the lid of the vacuum canister then reconnect it to the vacuum cleaner. Make sure to lock the vacuum canister in place properly.

Step 10. Turn your Hoover hurricane pet vacuum cleaner back on and you can start cleaning with it again.

How to replace the filter of a Hoover sprint stick cordless vacuum cleaner

Follow the steps below to change the filter of your Hoover sprint stick cordless vacuum cleaner properly . . .

Step 1. Turn your vacuum cleaner off and unplug it from the power outlet before you begin the replacement process. Replacing any part of your Hoover vacuum cleaner when the machine is turned on or plugged into the power outlet can cause electrocution.

Step 2. Disconnect the vacuum canister from the vacuum cleaner to gain access to the two filters. Set the rest of the vacuum cleaner aside.

Step 3. Open the lid of the vacuum canister and then empty it over a trash can.

Step 4. Turn the two filters counter clockwise to disconnect them from the vacuum canister.

Step 5. Take the filters out of the vacuum canister and then set them aside.

Step 6. Get new Hoover stick vacuum cleaner filters of the same kind and put them in the place of the old ones. Turn the new filters clockwise to lock them in place properly.

Step 7. Close the lid of the vacuum canister and reconnect it to the vacuum cleaner. Make sure to lock the vacuum canister in place properly.

Step 8. Turn your Hoover sprint stick cordless vacuum cleaner back on and you can start cleaning with it again.

How to replace the filter of a Hoover freedom stick vacuum cleaner

Follow the steps below to replace the filter of your Hoover freedom stick vacuum cleaner . . .

Step 1. Make sure your Hoover vacuum cleaner is turned off and unplugged from the power outlet before you start the replacement process.

Step 2. Disconnect the vacuum hose from the vacuum cleaner and then set it aside.

Step 3. Turn the vacuum cleaner upside down.

Step 4. Press the button at the bottom of the vacuum cleaner to disconnect the vacuum canister from the rest of the machine.

Step 5. Take the vacuum canister out of the vacuum cleaner and then set it aside.

Step 6. Twist the mesh filter counter clockwise to disconnect it from the main body of the vacuum cleaner. Take the mesh filter out of the vacuum cleaner and then set it aside.

Step 7. Get a new Hoover vacuum cleaner filter of the same kind and put it in the place of the old one. Twist the new filter clockwise to lock it in place properly.

Step 8. Reconnect the vacuum canister and make sure to lock it in place properly.

Step 9. Reconnect the vacuum hose to the vacuum cleaner.

Step 10. Turn your Hoover freedom stick vacuum cleaner back on and you can start cleaning with it again.

How to change the filter of a Hoover unplugged stick cordless vacuum cleaner

Follow the steps below to change the filter of your Hoover unplugged stick cordless vacuum cleaner . . .

Step 1. Ensure that your machine is turned off and unplugged from the power outlet before you start. Replacing any part of your Hoover unplugged stick cordless vacuum cleaner when the machine is turned or plugged into the power outlet can cause electrocution.

Step 2. Press the button at the bottom of the vacuum canister to disconnect it from the rest of the vacuum cleaner. Set the rest of your vacuum cleaner aside.

Step 3. Take the inner filter and the outer filter out of the vacuum canister and then set them aside.

Step 4. Get new Hoover vacuum cleaner filters of the same kind and put them in the place of the old ones.

Step 5. Reconnect the vacuum canister to the vacuum cleaner and make sure to lock it in place properly.

Step 6. Turn your Hoover unplugged stick cordless vacuum cleaner back on and you can start cleaning with it again.

How to replace the filter of a Hoover 14 4v free motion handstick vacuum cleaner

Follow the steps below to replace the filter of your Hoover 14 4v free motion handstick vacuum cleaner . . .

Step 1. Make sure your Hoover vacuum cleaner is turned off and unplugged from the power outlet before you start the replacement process.

Step 2. Press the button above the vacuum canister to disconnect it from the vacuum cleaner. Take the vacuum canister out of the vacuum cleaner and then set the rest of your machine aside.

Step 3. Take the lid of the vacuum canister out if the rest of the container. Set the vacuum canister lid aside.

Step 4. Take the filter out of the vacuum canister and then set it aside.

Step 5. Get a new Hoover stick vacuum cleaner filter of the same kind and put it in the place of the old one.

Step 6. Close the lid of the vacuum canister again and then reconnect it to the vacuum cleaner. Make sure to lock the canister in place properly.

Step 7. Turn your Hoover 14 4v free motion handstick vacuum cleaner back on and you can start cleaning with it again.

How to replace the filter of a Hoover 22v freedom plus vacuum cleaner

Follow the steps below to replace the filter of your Hoover 22v freedom plus vacuum cleaner . . .

Step 1. Turn your vacuum cleaner off and unplug it from the power outlet before you start the replacement process.

Step 2. Flip the vacuum cleaner over.

Step 3. Empty the vacuum canister and then disconnect it from the vacuum cleaner. Set the vacuum canister aside.

Step 4. Take the first filter out of the bottom of the vacuum cleaner and then set it aside.

Step 5. Get a new Hoover vacuum cleaner filter of the same kind and put it in the place of the old one. Make sure to lock the new filter in place properly.

Step 6. Reconnect the vacuum canister to the vacuum cleaner.

Step 7. Flip the vacuum cleaner over again and then turn it backwards.

Step 8. Press the button at the back of the vacuum cleaner to disconnect the second filter from the rest of the machine. Set the second filter aside.

Step 9. Get a new Hoover vacuum cleaner filter of the same kind and put it in the place of the old one. Make sure to lock the new filter in place properly.

Step 10. Turn your Hoover 22v freedom plus vacuum cleaner back on and you can start cleaning with it again.

Are Hoover Vacuum Cleaner Filters Washable?

Yes, you can wash the filter of your Hoover vacuum cleaner if you want to clean it more thoroughly.

Hoover Vacuum Cleaner Filter Pops Out – Why and How To Fix

If the filter of your Hoover vacuum cleaner keeps popping out, the problem could be that it is clogged. To solve the problem, you will need to wash the filter. After washing the filter of your Hoover vacuum cleaner, turn the machine back on and check if the filter stops popping out.

Leave a Comment