When you get a new Bissell vacuum cleaner, you will need to learn how to use it. Here’s a quick guide on how to use a Bissell vacuum cleaner . . .
Table of Contents
How To Use Bissell Vacuum
Follow the steps below to use your Bissell vacuum cleaner properly . . .
Step 1. Take your Bissell vacuum cleaner out of its packaging.
Step 2. Charge the vacuum cleaner for about five hours until you are sure it is full. When the vacuum cleaner is full, you will see a solid blue light flashing for about ten minutes. Unplug the vacuum cleaner from the power outlet once it is fully charged.
Step 3. Press the red lever on the side of the vacuum cleaner with your foot to turn it on . Press the red lever again to turn the vacuum cleaner off when you are done cleaning..
Step 4. Press the blue lever below the red lever with your foot to lean the vacuum cleaner back for cleaning convenience.
Step 5. If you want to lean the vacuum cleaner even lower, press the blue lever a second time.
Step 6. When you are done cleaning, move the vacuum cleaner back into the upright position to lock the blue lever into place.
Step 7. Use the blue knob at the bottom of the vacuum cleaner to adjust it to your desired setting.
Step 8. If the vacuum cleaner is too hard to push, you will need to change it to a higher setting.
Step 9. The vacuum cleaner comes with different accessories for cleaning different areas. To use the accessories simply connect them to the vacuum wand.
You can start using your Bissell vacuum cleaner now.
How To Use Bissell Vacuum And Mop
Follow the steps below to use your Bissell crosswave mop vacuum cleaner . . .
Step 1. Take your Bissell crosswave vacuum cleaner out of its packaging.
Step 2. Charge the vacuum cleaner for about five hours until it is full. You will see a solid blue light flashing when the vacuum cleaner is full.Unplug the vacuum cleaner once it is fully charged.
Step 3. Slide the handle into the vacuum cleaner until you hear it lock with a click.
Step 4. Fill the water tank with your desired amount of water.
Step 5. Slide the water tank into the back of the vacuum cleaner until you hear it lock with a click.
Step 6. Plug the machine into the power socket to start it then select your desired setting.
Step 7. Recline the vacuum cleaner and the brush roller should start spinning.
Step 8. Hold the trigger for about ten seconds to prime the brush roller with water and cleaning solution. You can start cleaning with your vacuum cleaner now.
Step 9. Use the Easy Storage Tray to store the vacuum cleaner when you are done cleaning.
How To Use Bissell Vacuum Attachments
Follow the steps below to use your Bissell vacuum cleaner attachments . . .
Step 1.Turn your Bissell vacuum cleaner off then unwind the flex hose from the rack at the back of the vacuum cleaner.
Step 2. Choose your desired attachment in the tool caddy at the back of the vacuum cleaner.
Step 3.Connect your desired attachment to the end of the flex hose.
Step 4. Place the Ready Tools Dial on the front of the vacuum cleaner to the hose attachment setting if you want to pick up dirt while spraying water from the hose.
Step 5. If you want to rinse carpets or upholstery, set the Custom Clean Dial to the rinse setting.
Step 6. Turn your Bissell vacuum cleaner on. You can start cleaning with your vacuum cleaner now.
How To Use A Bissell Symphony Vacuum And Steam Mop
Follow the steps below to use your Bissell symphony vacuum cleaner and steam mop properly. .
Step 1. Take the vacuum cleaner out of its packaging.
Step 2. Charge the vacuum cleaner until it is full. You can tell that the vacuum cleaner is fully charged when you see a solid blue light flashing. Unplug the vacuum cleaner once it is full.
Step 3. Push the main part of the vacuum cleaner into the lower base of the vacuum until you hear it lock with a click.
Step 4. Insert the handle into the main part of the vacuum cleaner.
Step 5. Tilt the lever at the back of the vacuum cleaner to adjust the vacuum handle to your desired height.
Step 6. Fill the water tank with water. The water in the water tank can last for about fifteen minutes depending on the amount of steam used during the cleaning process
Step 7. Turn the vacuum cleaner on.
Step 8. If you want to use the steam setting, press the trigger at the back of the vacuum cleaner handle.
Step 9. When you are done cleaning, wrap the vacuum cleaner cord around the hooks at the back of the vacuum cleaner.
Step 10. When you are done cleaning, disconnect the mop from the vacuum cleaner and then air dry it before putting it back into the vacuum.
Step 11. When using the steam mop, you will have to wait for about sixty seconds for the washer to heat up before using.
Step 12. Always empty the dirt container after vacuuming.
Step 13. Charge the vacuum cleaner after each use. You can start using your Bissell symphony vacuum and steam mop now.
How To Use A Bissell Carpet Vacuum Cleaner
Follow the steps below to use your Bissell carpet vacuum cleaner properly . . .
Step 1. Take your Bissell carpet vacuum cleaner out of its packaging.
Step 2. Charge the vacuum cleaner for about hours until it is full. You can tell that the vacuum is fully charged when you see a solid blue light flashing. Unplug the vacuum cleaner once it is full.
Step 3. Clear out the furniture from the area that you want to clean.
Step 4. Clean the carpet with a normal vacuum cleaner to stop the carpet cleaner from pushing dirt deeper into the carpet later.
Step 5. Use carpet shampoo to get rid of stubborn stains in the carpet.
Step 6. Fill the carpet cleaner’s water tank with hot water. Make sure you do not let it go past the maximum point.
Step 7. Add some of your carpet cleaning formula to the water tank.
Step 8. Select your desired cleaning setting. Turn the cleaning dial to select the clean setting.
Step 9. Plug the vacuum cleaner into a power outlet then flip both switches at the back of the carpet cleaner to turn it on and activate the heating system.
Step 10. Push the trigger at the bottom of the vacuum cleaner to spray water while cleaning.
Step 11. Go over the same areas a second time to suck up dirt and water that may still be on the carpet.
Step 12. Empty the water tank once it is full of dirty water.
Step 13. To use the cleaning attachments, turn the clean dial to the tool setting then select your desired attachment. The cleaning tools are useful for cleaning areas that are hard to reach.
How To Use The Hose On A Bissell Vacuum
Follow the steps below to use the hose of your Bissell vacuum cleaner . . .
Step 1. Turn your Bissell vacuum cleaner on.
Step 2. Make sure the hose is properly connected to the vacuum cleaner.
Step 3. Use the extended reach hose to make the hose even longer.
Step 4. Attach the lower main hose to the extended reach hose.
Step 5. Attach your desired cleaning attachment to the hose. You can start using the vacuum cleaner now.
